Description

Aquacoat 1984 is a permanent, waterbased release agent for all kind of rubber. 1984 requires a short baking time. Aquacoat 1984 is a permanent water-based release system designed for moulding operations when non-transfer of release agent, high temperature stability, high degree of slip, and abrasion resistance of the release film are important. Aquacoat 1984 is water thin liquid and ready to use. The release system becomes functional after cure. The release film is micro thin and stable until 400°C. Aquacoat 1984 adheres to mould surfaces and provides multiple releases with virtually no transfer to moulded parts. Aquacoat 1984 reduces build-up on moulds when applied according to instructions.

Description of Application Ranges

Permanent coating for all kind of rubber. Polyester, Epoxy, Prepreg

Description

SK-44 is a permanent waterbased release agent designed for the production of silicone rubber parts.

Description of Application Ranges

Permanent release agent, especially suitable for silicone rubber.

Description

DRW-299 is a semipermanent,waterbased release agent for AL,Mg, Zn. - easy to use - high temperature stability (until 1200 Celcius) - paintable - excellent release

Description of Application Ranges

semipermanent release agent

Description

Permcoat 1984 green is a permanent solvent based release and coating system designed for moulding and protection operations when non-transfer of release agent, high temperature stability, high degree of slip, and abrasion resistance of the release film are important.
Permcoat 1984 green is liquid and ready to use. The release and coating system becomes functional after cure. The film is micro thin and stable until 600°C.
Permcoat 1984 green adheres to the coated surfaces and provides multiple releases or long lasting protection with no transfer to moulded parts.
Permcoat 1984 green reduces build-up on moulds when applied according to instructions.

Description of Application Ranges

Rubber, all kind of rubber-types and rubber moulding (except silicone rubber)
Especiall suitable for protection coatings against bonding agent!

Description

Aquacoat 1984 is a permanent water-based release system and protection coating designed for moulding operations when non-transfer of release agent, high temperature stability, high degree of slip, and abrasion resistance of the release film are important.
Aquacoat 1984 is water thin liquid and ready to use. The release system becomes functional after cure. The release film is micro thin and stable until 450°C.
Aquacoat 1984 adheres to mould surfaces and provides multiple releases with virtually no transfer to moulded parts.
Aquacoat 1984 reduces build-up on moulds when applied according to instructions.

Description of Application Ranges

Rubber, all kind of rubber-types and rubber moulding (except silicone rubber)

Description

Glasscoat 754 is applied to blank and mould equipment to facilitate a start-up during job changes. Glasscoat 754 will ensure a smooth start-up and minimize lost production. Glasscoat 754 allows operators to focus their attention on fine-tuning various parameters of the I.S. machine and checking bottle quality, rather than on swabbing. This contributes to minimizing the time required to start producing bottles of acceptable quality.
Rather than waiting 10 to 20 minutes to pack the first bottle after a job change, with a good pre-coat, production of bottles of an acceptable quality can usually begin right away assuming that the mould equipment is heated to operating temperature before being put into service.
Glasscoat 754 a water based semi-permanent, non-toxic, non-hazardous coating used as a glass release agent for blanks, molds, neck rings, bottom plates, and related equipment in the glass container industry. It is supplied as a 1- component product. Glasscoat 754 is a mix of surfactants, polymers, adhesives and graphite.
Glasscoat 754 should be applied by a spray gun and will form a smooth, uniform, tightly bonded film of graphite onto mold equipment surfaces.

Description

SK-44 M is a semi-permanent water-based release system designed for moulding operations when non-transfer of release agent, high temperature stability, high degree of slip, and abrasion resistance of the release film are important.
SK-44 M is water thin liquid and ready to use. The release system becomes functional after cure. The release film is micro thin and stable until 260°C.
SK-44 M adheres to mould surfaces and provides multiple releases with virtually no transfer to moulded parts.
SK-44 M reduces build-up on moulds when applied according to instructions.

Description of Application Ranges

Silicone rubber, will give an excellent matt surface of the produced parts.