Description

RA-336 is a special internal release agent added directly to any aqueous resin system (melamine, phenol or urea aqueous resin mixture), used for high pressure and low pressure impregnation. - low dosage - faster press cycle time - reduces build up - low foaming

Description of Application Ranges

Technical Data Sheet for High-pressure and Low-pressure impregnation

Description

MF-352 B is a waterbased modifier which is based on a combination of Acrylat Resin, Glycols and Amines. MF-352 B has a low viscosity and comes in a clear and liquid form. - better flow properties - higher gloss - higher flexibility - no cracks on the surface

Description of Application Ranges

waterbased modifier

Description

Latent hardener for melamine formaldehyde impregnation resins with long pot-life and high curing activity. CA-340 shows no tendency to blistering in films and does not disturb the flow of the resin in the press during the coating process. - no sagging of resin - long pot life - faster press cycle

Description of Application Ranges

Latent hardener for melamine formaldehyde impregnation resins

Description

AB-310 is well suited for the decorative coating of plane carrier materials (e.g. chip boards, fiber boards, sheets on bases of phenolic resins a.s.o.). - excellent release - no sticking of palletized paper - low dosage even at high humidity

Description of Application Ranges

Universal Anti-Block-System for amino plastic resin solution

Description

MF-352 is a water based modifier which is based on Acrylat Resins and Amines.
The product has a low viscosity and comes in a clear and liquid form.

Description

Latent hardener for melamine formaldehyde impregnation resins with long pot-life and high curing activity.

Description

Latent hardener for urea formaldehyde impregnation resins with long pot-life and high curing activity. CA-341 does not contain chloride ions.

Description

WT-320-0 is the ideal wetting agent for melamine-formaldehyde, urea formaldehyde resins and impregnation of decor papers which are difficult to process. WT-320-0 effectively reduces the surface tension of the resin allowing for better penetration in the paper. The levelling characteristics will provide coatings free of fish-eyes, streaking and air blisters. This additive prevents pigment loss (dusting), bleeding in resin bath, and boosts the effect of hardeners in melamine formaldehyde resins without producing negative effects on the resin spot life. The reduction in resin surface tension and increased flow efficiency should be reduce the quantity of resin required for coating. Dosage percentage levels should be tested initially at the lowest recommended levels. If the desired results are not achieved, the dosage should be increased until the upper level is reached.

WT-320-0 can be used in combination with other additives to solve many product and process problems.

Description

RA-330/0 is a special internal release agent added directly to any aqueous resin system (melamine, phenolic or urea aqueous resin mixture), used for high pressure and low pressure impregnation. Basic requirements for release agents for aqueous resins are fully met by
RA-330/0.

1. Shorting or pressing time (down to under 20 sec.)
2. Prevention of formation of deposits on the press plates. The result can be 2-3 times extended tool service life a reduction in production stoppages and lower production costs.
3. RA-330/0 also acts as an ideal stabilizer for resins in transit or storage.

RA-330/0 consist of synthetic resins and surfactant substances. Special emulsifiers enable complete compatibility with many resin system regardless of resin bath standing time. Storage at low temperatures may cause partial sedimentation, but dissolves again between 20-40 °C.
Dosage levels of TAG additives should be tested initially at the lowest recommended levels. If the desired results are not achieved; the dosage should be increased in increments until the upper dosage level is reached.

RA-330/0 can be used in combination with other TAG additives to solve many product and process problems.

Description

CP-350 is a water-borne, self binding preparation of white colour pigments. It is designed for application with aminoplast resins to produce laminating foils.
CP-350 has a very high opacity and is especially adapted for surface coatings with impregnated paper.
CP-350 is based on a mixture of titaniumdioxyde, acrylic copolymers, water and inorganic extenders.

Description

AD-362 is an universal Anti-Dust product for the laminating process.
AD-362 has excellent properties to smoothen the surface of the impregnated paper and prevent it from dust.
AD-362 is mainly used for MDF resin application in the second vat or raster station.
AD-362 provides a high colour saturation.

Description

MF-358 is a special modifier for Melamine-Formaldehyde Resins.
The product comes in a clear and liquid form.

Description

CA-342 MU is a high performance hardener for melamine and urea formaldehyde impregnation resins with high curing activity.

Description of Application Ranges

CA-342 MU can be used in all melamine and urea resins which are used for coating of support material such as chipboards, fibreboards and laminated plastic sheets.

Description

AF-707TX is a defoamer which shows already at very low dosage excellent results.
AF-707TX is a mixture of modified polymers.
AF-707TX is ready to use and can be added directly to waterbased systems

Description of Application Ranges

Universal usage. Especially suitable for waterbased systems